Posts Tagged: plumbing technician

Can Toilet Paper Clog Your Toilet?

Does your toilet gets clogged frequently? It’s a messy, unpleasant, inconvenient experience, and you probably would be glad if it never happened again. In order to prevent clogs, you make sure to never flush anything that could be damaging, like food, feminine hygiene products, or trash. But what if the clogs keep forming?

As strange as it sounds, toilet paper may cause your constant clogs. Not all toilet paper is made the same, and some things may get stuck in your plumbing (apofraxeis Kallitheas). This post can help you figure out why toilet paper might clog your toilet and what to do about it.

Why Does Toilet Paper Form Clogs?

You would think that since toilet paper is designed to go into the toilet, it wouldn’t cause any problems. However, that isn’t always the case – there are a few reasons why toilet paper clogs form:

  • Low-flow toilets. You may have chosen a low-flow toilet for its efficiency. After all, you care about the environment, and you don’t want to waste water. You also want your water bill to remain low. However, because low-flow toilets use less water, the water pressure isn’t as high. Therefore, the thickness of the toilet paper used is something to be aware of.
  • Rough pipes. New pipes are smooth and clean, which means that waste goes through them easily. However, the pipes get coated in grease and waste over time, and the edges may get rougher. All of these factors can cause toilet paper to become stuck more easily. Older cast iron pipes can be more at risk for clogs.
  • Too much toilet paper. As you have doubtless observed, too much toilet paper can clog your toilet. Generally, adults tend to know how much toilet paper is too much, so this probably isn’t an issue for you. However, if you have a child who is still learning, you may have to deal with clogs frequently.
  • Toilet paper that doesn’t dissolve well. You may love getting ultra-plush toilet paper-you want a product that is soft, absorbent, and strong. However, if you get a toilet paper that is too thick, it may not dissolve very well, which means that it can get stuck in your pipes and cause clogs. If you eliminate other reasons why your toilet is clogging, your toilet paper itself might be to blame.

Your clogging problem may be caused by one issue or a combination of problems. You may have to do some experimenting to get rid of the problem.

How Can I Stop Clogs?

The annoying part about toilet paper clogging your toilet is that it’s 100% preventable. Some countries may not flush anything, including toilet paper. In Canada, we like to flush our used toilet paper with our waste. The most important thing you can do to prevent clogs is to limit the amount of toilet paper per flush, even if it results in multiple flushes. 

Plumbing and Drainage Contractors – Αποφράξεις Αθήνας – also suggest that you be more scrutinizing in terms of toilet paper selection. While toilet paper companies market their ultra-soft, ultra-thick toilet paper, it’s actually not ideal for your plumbing system. The thicker the toilet paper, the longer it takes for it to dissolve. Your three criteria in toilet paper selection are:

  • Soft to the touch.
  • Strong enough so that it does not fall to pieces when you use it.
  • Has a fast rate of dissolving.

To keep yourself from going cross-eyed while strolling the aisles at the supermarket, put the plunger down and spend a little time on the Internet. Research a good toilet paper that fits your needs and your plumbing system. Compare one, two, and three-ply versions and check out other categories, such as:

  • Absorbency
  • Softness
  • Strength
  • Clog-ability

There are many brands on the market, so one is bound to fit the bill! Constant plumbing repairs can now be a thing of the past.

A Not-So Definitive Solution

As it turns out, this issue isn’t black and white. It is the amount and volume of toilet paper that dictates no matter whether or not a clog and more plumbing repairs will result. Using a minimal amount of rest room paper amongst flushes will maintain your system healthy and free from injury. On the other hand, if you use fifty percent a roll at a time, be geared up to suffer the effects!

Any toilet paper made with 100% recycled paper will dissolve almost completely. It is the best toilet paper to use.

Instead of being made up of long, strong fibers, recycled paper has short fibers that easily break apart into short little pieces.

The tinier the pieces are, the less likely they are to get caught on the edges, rough spots, or corners in your plumbing. No getting caught means no clogging means no running from the bathroom being chased by a lava-like flow of poo.

What exactly is recycled toilet paper made of?

Recycled toilet paper isn’t made up of used toilet paper. It’s made up of post consumer recycled content (PCR). The bad part of that is the fact that this includes papers that have BPA in them. 

Things like credit card printouts and lottery tickets are made with paper that has BPA. Those things are then added to the other papers that consumers recycle (like cardboard) and end up getting BPA into the recycled paper.

HOWEVER the amount of BPA is minimal (we’re talking parts per billion) and if you’re going to weigh pros and cons, the pros of using recycled toilet paper far outweigh the cons. The BPA in recycled paper is insignificant compared to what we come into contact with daily.

What About When I’m Away From Home?

Did you know that in many countries, you aren’t supposed to flush the toilet paper? Generally, Western Europe, Canada, Australia, and the US all flush toilet paper, but much of the rest of the world doesn’t-and if you try to do so in those areas, you might clog the pipes. You probably don’t want to cause or deal with a plumbing emergency while on vacation.

If you plan on travelling in an unfamiliar country, make sure to look up how they handle toilet paper before you leave. However, if you are travelling now and you aren’t sure, just check the bathroom. If there is a waste-basket that has toilet paper in it already, you should probably throw the paper away instead of flushing it.

If your toilet keeps clogging just from waste and toilet paper, make sure you are using a small amount of the right kind of toilet paper. However, if you have further problems, contact Αποφράξεις Αντωνίου Καλλιθέας . We can help you address the problem and discuss your options, including replacing the toilet fixture.

See more about plumbing services:

8 Indications that you have to drain your water heater

One of the most obvious signs that you need to drain – ΑΠΟΦΡΑΞΕΙΣ ΠΕΡΙΣΤΕΡΙ – your water heater is that you are running out of hot water faster than normal. When the sediment builds up too much, the heating element in the tank is at risk of burning. Orange and rusty looking water is another sign that you should not ignore. This happens when the anode rod deteriorates.

If your water heater seems to be making more noises than normal, it could be another sign that your tank is dying. This happens when minerals build up over time and harden, and when the hot water is in there, it affects the brittle tank. Another important red flag to watch out for leaks in the tank. Over time the sediment breaks down the material of the tank and becomes rusty.

1. Prepare Your Water Heater

If you are learning how to drain a water heater, the most important tip is to prep your heater by turning it off. You will need to know what type of water heater you have for this step.

Electric water heaters typically have a switch that connects them to electricity. If you are having a difficult time locating the switch to turn it off, check for a board above the heater. If you use an electric heater, you need to ensure that the power is off before flushing the tank. They typically have their circuit breakers in the main electric panel. Those who have a gas-powered water heater should turn the switch to “pilot.” The pilot light will remain on when you do so, however, the water won’t continue to be heated.

2. Wait Before Continuing

It is highly recommended to let all of the water in the tank to fully cool off before continuing. Many people underestimate the amount of time that this could take. You should expect the water to take anywhere from a couple of minutes to hours to cool off. Depending on the size of the water heater, you may require more or less time.

Your water inlet valve should be in the “on” position during this stage. Waiting to continue before flushing the water pipes is crucial because you could run the risk of burning yourself or damaging items where the water will be released. Take extra precautions during this step.

3. Flush the Pipes

After waiting several hours, the next tip on how to drain a hot water tank is to flush the pipes. You will need to turn off the cold water inlet switch to properly do this step. This switch is often found towards the top of the heater. It is also where water accumulates before being heated.

Next, you will have you go to a sink in the house and turn on the hot water. It is recommended to go to the floor above where the water heater is located, if possible. Let the water run until it is cool and all excess water from the pipes is removed. The point of letting the water flow and flushing the pipes is to also relieve any pressure that may have built up in the pipes. It is important that once you have done these steps, that you open the pressure relief valve.

4. Connect to the Pump

Now that your water heater is fully prepped and you have your garden hose, you must connect it to the pump. You will need to know if your water heater sits above ground or below. If your water heater is above ground, your job is a little easier. You simply need to connect the hose to the tank. After that, you will have to let gravity force the water downwards and out of the tank.

Those who have a water heater underground will need to buy a small pump at the store to connect to the hose. On the other end, it will reattach to another hose to pull the water out or into a drain. You may also have to plug your pump in for it to work.

5. Evaluate and Decide

Collecting water in a bucket is highly recommended to determine if you need to fully flush your water drain. If the water heater is in good condition and clean, the water in the bucket should appear clean as well.

The watercolour and sediment build-up helps indicate the condition of the tank. If there is a large amount of sediment built up at the bottom of your bucket, you will need to flush out the water heater. If there isn’t much built up, you may be able to keep an eye on it and flush it later on.

6. Flush the Water Heater

To flush your water heater, you will need to disconnect the garden hose that you previously attached. You then have to turn off the water tap and the pressure relief valves. Next, fill the tank with water and drain again. You may need to repeat this step several times before fully draining the sediment.

Many people claim that pouring the sediment-water into the toilet is a good way to get rid of the liquid. It is important to keep in mind however, that it could leave stains. Be sure to fully clean your toilet if you choose to flush the water. Make sure that after each time that you drain the tank, you briefly turn on the cold water valve. This will release cold water into the tank to refill and drain again.

7. Put It Back Together

First, take off the garden hose and turn the pressure relief valve. You will also need to turn your gas and electricity intake back on by flipping their switches. Your water heater should preform normal once you follow all of these steps.

The water should begin filling to its standard amount and stop. You should then go back to the sink that you previously released the water pressure in the pipes and turn on the hot side. This will relieve back pressure within the tank. It should also fill up with water again.

Keep it running until a full stream of water is going. After you have completed this step and your tank is full, you can resume normal functioning. You may need to seek professional help if you are still having issues with the tank.

8. Monitor and Keep up on Maintenance

Monitoring and keeping up on routine maintenance is the best way to ensure optimal water heater performance. There are many things that you can do to improve the lifespan of your water heater. One of the best ways to prevent issues from arising is by placing your water heater in an empty area. Surrounding it with too many items can run the risk of cutting off airflow and even starting a fire. Another way to maintain your water heater is to adjust the temperature if you are leaving town for some time. You can either put the temperature on the lowest setting or completely turn it off until you come home.

See more about plumbing issues:

Show Buttons
Hide Buttons