Posts Tagged: plumber

Can Toilet Paper Clog Your Toilet?

Does your toilet gets clogged frequently? It’s a messy, unpleasant, inconvenient experience, and you probably would be glad if it never happened again. In order to prevent clogs, you make sure to never flush anything that could be damaging, like food, feminine hygiene products, or trash. But what if the clogs keep forming?

As strange as it sounds, toilet paper may cause your constant clogs. Not all toilet paper is made the same, and some things may get stuck in your plumbing (apofraxeis Kallitheas). This post can help you figure out why toilet paper might clog your toilet and what to do about it.

Why Does Toilet Paper Form Clogs?

You would think that since toilet paper is designed to go into the toilet, it wouldn’t cause any problems. However, that isn’t always the case – there are a few reasons why toilet paper clogs form:

  • Low-flow toilets. You may have chosen a low-flow toilet for its efficiency. After all, you care about the environment, and you don’t want to waste water. You also want your water bill to remain low. However, because low-flow toilets use less water, the water pressure isn’t as high. Therefore, the thickness of the toilet paper used is something to be aware of.
  • Rough pipes. New pipes are smooth and clean, which means that waste goes through them easily. However, the pipes get coated in grease and waste over time, and the edges may get rougher. All of these factors can cause toilet paper to become stuck more easily. Older cast iron pipes can be more at risk for clogs.
  • Too much toilet paper. As you have doubtless observed, too much toilet paper can clog your toilet. Generally, adults tend to know how much toilet paper is too much, so this probably isn’t an issue for you. However, if you have a child who is still learning, you may have to deal with clogs frequently.
  • Toilet paper that doesn’t dissolve well. You may love getting ultra-plush toilet paper-you want a product that is soft, absorbent, and strong. However, if you get a toilet paper that is too thick, it may not dissolve very well, which means that it can get stuck in your pipes and cause clogs. If you eliminate other reasons why your toilet is clogging, your toilet paper itself might be to blame.

Your clogging problem may be caused by one issue or a combination of problems. You may have to do some experimenting to get rid of the problem.

How Can I Stop Clogs?

The annoying part about toilet paper clogging your toilet is that it’s 100% preventable. Some countries may not flush anything, including toilet paper. In Canada, we like to flush our used toilet paper with our waste. The most important thing you can do to prevent clogs is to limit the amount of toilet paper per flush, even if it results in multiple flushes. 

Plumbing and Drainage Contractors – Αποφράξεις Αθήνας – also suggest that you be more scrutinizing in terms of toilet paper selection. While toilet paper companies market their ultra-soft, ultra-thick toilet paper, it’s actually not ideal for your plumbing system. The thicker the toilet paper, the longer it takes for it to dissolve. Your three criteria in toilet paper selection are:

  • Soft to the touch.
  • Strong enough so that it does not fall to pieces when you use it.
  • Has a fast rate of dissolving.

To keep yourself from going cross-eyed while strolling the aisles at the supermarket, put the plunger down and spend a little time on the Internet. Research a good toilet paper that fits your needs and your plumbing system. Compare one, two, and three-ply versions and check out other categories, such as:

  • Absorbency
  • Softness
  • Strength
  • Clog-ability

There are many brands on the market, so one is bound to fit the bill! Constant plumbing repairs can now be a thing of the past.

A Not-So Definitive Solution

As it turns out, this issue isn’t black and white. It is the amount and volume of toilet paper that dictates no matter whether or not a clog and more plumbing repairs will result. Using a minimal amount of rest room paper amongst flushes will maintain your system healthy and free from injury. On the other hand, if you use fifty percent a roll at a time, be geared up to suffer the effects!

Any toilet paper made with 100% recycled paper will dissolve almost completely. It is the best toilet paper to use.

Instead of being made up of long, strong fibers, recycled paper has short fibers that easily break apart into short little pieces.

The tinier the pieces are, the less likely they are to get caught on the edges, rough spots, or corners in your plumbing. No getting caught means no clogging means no running from the bathroom being chased by a lava-like flow of poo.

What exactly is recycled toilet paper made of?

Recycled toilet paper isn’t made up of used toilet paper. It’s made up of post consumer recycled content (PCR). The bad part of that is the fact that this includes papers that have BPA in them. 

Things like credit card printouts and lottery tickets are made with paper that has BPA. Those things are then added to the other papers that consumers recycle (like cardboard) and end up getting BPA into the recycled paper.

HOWEVER the amount of BPA is minimal (we’re talking parts per billion) and if you’re going to weigh pros and cons, the pros of using recycled toilet paper far outweigh the cons. The BPA in recycled paper is insignificant compared to what we come into contact with daily.

What About When I’m Away From Home?

Did you know that in many countries, you aren’t supposed to flush the toilet paper? Generally, Western Europe, Canada, Australia, and the US all flush toilet paper, but much of the rest of the world doesn’t-and if you try to do so in those areas, you might clog the pipes. You probably don’t want to cause or deal with a plumbing emergency while on vacation.

If you plan on travelling in an unfamiliar country, make sure to look up how they handle toilet paper before you leave. However, if you are travelling now and you aren’t sure, just check the bathroom. If there is a waste-basket that has toilet paper in it already, you should probably throw the paper away instead of flushing it.

If your toilet keeps clogging just from waste and toilet paper, make sure you are using a small amount of the right kind of toilet paper. However, if you have further problems, contact Αποφράξεις Αντωνίου Καλλιθέας . We can help you address the problem and discuss your options, including replacing the toilet fixture.

See more about plumbing services:

8 Indications that you have to drain your water heater

One of the most obvious signs that you need to drain – ΑΠΟΦΡΑΞΕΙΣ ΠΕΡΙΣΤΕΡΙ – your water heater is that you are running out of hot water faster than normal. When the sediment builds up too much, the heating element in the tank is at risk of burning. Orange and rusty looking water is another sign that you should not ignore. This happens when the anode rod deteriorates.

If your water heater seems to be making more noises than normal, it could be another sign that your tank is dying. This happens when minerals build up over time and harden, and when the hot water is in there, it affects the brittle tank. Another important red flag to watch out for leaks in the tank. Over time the sediment breaks down the material of the tank and becomes rusty.

1. Prepare Your Water Heater

If you are learning how to drain a water heater, the most important tip is to prep your heater by turning it off. You will need to know what type of water heater you have for this step.

Electric water heaters typically have a switch that connects them to electricity. If you are having a difficult time locating the switch to turn it off, check for a board above the heater. If you use an electric heater, you need to ensure that the power is off before flushing the tank. They typically have their circuit breakers in the main electric panel. Those who have a gas-powered water heater should turn the switch to “pilot.” The pilot light will remain on when you do so, however, the water won’t continue to be heated.

2. Wait Before Continuing

It is highly recommended to let all of the water in the tank to fully cool off before continuing. Many people underestimate the amount of time that this could take. You should expect the water to take anywhere from a couple of minutes to hours to cool off. Depending on the size of the water heater, you may require more or less time.

Your water inlet valve should be in the “on” position during this stage. Waiting to continue before flushing the water pipes is crucial because you could run the risk of burning yourself or damaging items where the water will be released. Take extra precautions during this step.

3. Flush the Pipes

After waiting several hours, the next tip on how to drain a hot water tank is to flush the pipes. You will need to turn off the cold water inlet switch to properly do this step. This switch is often found towards the top of the heater. It is also where water accumulates before being heated.

Next, you will have you go to a sink in the house and turn on the hot water. It is recommended to go to the floor above where the water heater is located, if possible. Let the water run until it is cool and all excess water from the pipes is removed. The point of letting the water flow and flushing the pipes is to also relieve any pressure that may have built up in the pipes. It is important that once you have done these steps, that you open the pressure relief valve.

4. Connect to the Pump

Now that your water heater is fully prepped and you have your garden hose, you must connect it to the pump. You will need to know if your water heater sits above ground or below. If your water heater is above ground, your job is a little easier. You simply need to connect the hose to the tank. After that, you will have to let gravity force the water downwards and out of the tank.

Those who have a water heater underground will need to buy a small pump at the store to connect to the hose. On the other end, it will reattach to another hose to pull the water out or into a drain. You may also have to plug your pump in for it to work.

5. Evaluate and Decide

Collecting water in a bucket is highly recommended to determine if you need to fully flush your water drain. If the water heater is in good condition and clean, the water in the bucket should appear clean as well.

The watercolour and sediment build-up helps indicate the condition of the tank. If there is a large amount of sediment built up at the bottom of your bucket, you will need to flush out the water heater. If there isn’t much built up, you may be able to keep an eye on it and flush it later on.

6. Flush the Water Heater

To flush your water heater, you will need to disconnect the garden hose that you previously attached. You then have to turn off the water tap and the pressure relief valves. Next, fill the tank with water and drain again. You may need to repeat this step several times before fully draining the sediment.

Many people claim that pouring the sediment-water into the toilet is a good way to get rid of the liquid. It is important to keep in mind however, that it could leave stains. Be sure to fully clean your toilet if you choose to flush the water. Make sure that after each time that you drain the tank, you briefly turn on the cold water valve. This will release cold water into the tank to refill and drain again.

7. Put It Back Together

First, take off the garden hose and turn the pressure relief valve. You will also need to turn your gas and electricity intake back on by flipping their switches. Your water heater should preform normal once you follow all of these steps.

The water should begin filling to its standard amount and stop. You should then go back to the sink that you previously released the water pressure in the pipes and turn on the hot side. This will relieve back pressure within the tank. It should also fill up with water again.

Keep it running until a full stream of water is going. After you have completed this step and your tank is full, you can resume normal functioning. You may need to seek professional help if you are still having issues with the tank.

8. Monitor and Keep up on Maintenance

Monitoring and keeping up on routine maintenance is the best way to ensure optimal water heater performance. There are many things that you can do to improve the lifespan of your water heater. One of the best ways to prevent issues from arising is by placing your water heater in an empty area. Surrounding it with too many items can run the risk of cutting off airflow and even starting a fire. Another way to maintain your water heater is to adjust the temperature if you are leaving town for some time. You can either put the temperature on the lowest setting or completely turn it off until you come home.

See more about plumbing issues:

What Is a Clean out in Plumbing and why do you need them?

A pipes clean out offers a hassle-free area to access a building’s drain pipelines to clear clogs and particles. You can eliminate a cap on the clean out to supply the needed gain access to. According to apofraxeis vyronas the plumbing codes of many regions need the installation of clean outs throughout the plumbing rough-in during structure construction.

Clean out Components

A pipes clean out contains the main body as well as a threaded cap. The body is usually the exact same size as the drain pipeline where it will be mounted. The expansion is the portion of the body that the cap is threaded right into as well as is developed to be easily accessible in the event of a clog. The cap should be 2 inches over the degree of the floor or the ground outside.

Clean out Location

A clean out may be inside a structure or outdoors. A clean out that is outside the structure should have a cap noticeable within a few feet of the building’s structure. A clean out situated inside the structure may be inside a wall surface or flooring. A clean out might be easily obtainable in buildings that have a crawlspace or a basement. Clean outs are typically in the drainpipe where there is a 90 degree turn and also placed as though when you get rid of the cap you can conveniently service the blockage.

Eliminating the Cap

Location a large pail under the cap if it is located inside the structure to catch any fluid that might still be in the lines. Readjust a monkey wrench to fit the square fitting on the end of the cap. Area the wrench over the suitable and also turn it in a counter-clockwise instructions to loosen up the fitting. Remove the wrench as well as twist the cap off by hand.

Clearing a Clog

A pipes auger looks like a huge power drill and it offered for lease in the house or pipes centres. Switch on the auger and also feed it right into the clean-out expansion. Some augers will certainly extend instantly to reach the obstruction. Utilize a yard tube with a high pressure suggestion if you do not have access to an auger. Do not make use of a pipe if the clean out is inside the residence. Coat the strings of the cap with pipe dope and also tighten it into area with a pipe wrench to give a great seal versus sewer gas.

Yet suppose I do not have a drainpipe clean out?

If you do not have drainpipe clean outs, backups can still be eliminated but it can often be a lot more tough. The plumbing professional has 2 choices in this circumstance: gain access to the sewer line from the roof or from the commode. Sadly, neither option is as efficient as going in with a clean out.

Choice # 1: Get rid of The Blockage From The Roofing system

The sewage system line can be accessed from the roofing, however it is difficult to get a camera via due to the numerous turns in the pipelines. In many scenarios, the video camera or drain equipment can not reach the primary sewer line and the backup can not be eliminated. Another trouble is that it is extra dangerous. It can also be harmful for plumbings, particularly in winter season or during bad weather. There are times when it is too unsafe for our plumbing professionals to go on the roof covering.

Alternative # 2: Eliminate Toilet

If you do not have clean outs, eliminating the bathroom may be your only alternative. This boosts the price of labour and also the threat of damages to the toilet itself. After the commode is gotten rid of, the plumbing can after that make use of a drainpipe equipment to remove the obstruction. Nevertheless, the clog may not be eliminated as extensively because the pipelines underneath the toilet are smaller sized.

Both of these are less effective at getting rid of clogs. You may continue to have troubles as well as regular back-ups since you do not understand what created the blockage. Did the youngsters flush a toy auto or are origins from the tree in your backyard turning into your pipelines? A lot of times plumbers can not service warranty their work if they can unclear the drainpipe troubles via clean outs.

So what is the remedy?

Every home is special and also numerous variables enter into play when making a decision whether or not to install clean outs. Αποφράξεις Βύρωνα accredited plumbing professionals can examine your pipes demands as well as help you determine if this option is a great fit for you. As a general regulation, clean outs are a terrific choice for the following reasons:

Protects against regular drain problems

You wish to prevent obstructions rather than repair them later. With a drainpipe clean out, the plumber can tell you precisely what is creating the trouble and give referrals for avoiding them in the future.

Drain specific clean outs

If a particular drain remains to offer you problems, you might want to install a clean out specific to that drain. With drainpipe details clean outs, repairs end up being a lot easier.

May increase home resell worth if purchasers request a drain inspection

Clean outs make residence assessments simpler as a result of just how simple it is to send a camera through the line. It provides the potential customer satisfaction relating to the problem of the plumbing. It can additionally decrease the expense of drain fixings in the future.

What’s the Bottom Line?

Drain clean outs make it simpler to deal with clogged up pipes. It additionally makes it simpler to recognize problems in your drainpipe line that runs from your house to the sewage system or sewage-disposal tank. You will certainly know precisely what the issue is as well as how to avoid it in the future.

See more about Plumbers :

Do Plumbers Charge For Estimates?

Do plumbers charge for estimates?

That is an excellent question. As most plumbing companies are concerned they are individual companies and have the right to have their own policy. That means some may charge for an estimate, and others may not. Personally I think it is a ridiculous practice to charge the consumer for an estimate.

Being in the plumbing business in the Virginia area for well over a decade. I have seen plumbers come and go. I have asked many of those that do charge for an estimate why they do it and there are two different lines of thinking. The first is mainly because people often call a plumber out just to discover the solution to their current problem. They will then turn around and attempt to do it themselves. This is a blatant abuse of the system. People like that make it bad for everyone.

The second reason I have discovered why most plumbing companies started charging for an estimate stems from the first. They want to avoid wasting their time, going out for no reason. Many of these plumbers will take the cost of the estimate off of your invoice if you do decide to use their services.

Im my personal opinion if a plumbing company attempts to charge you for an estimate, that is a sign that their business is not doing well. In most cases these are what is known as fly-by-night handymen. They do not have any insurance, nor are they licensed. This is up to the consumer to ask the right questions.

Here at our Plumbing compamy HVAC we have never charged a customer for coming out and giving an estimate. Although we have encountered those do-it-yourself types that have no intention on using our service, we go out anyway. Those types are far and few, and all part of doing business.

See more about plumbing problems and services:

 

Show Buttons
Hide Buttons